Suction & Skimmer Fittings - Spas & Spa Baths

Many spa suction fittings no longer comply with the current standards requiring specific testing and flow rates to be listed. If you don't see your suction fitting here, this is the likely reason.

For new installations and re-plumbs, the use of approved suctions of the correct flow rate is required. 
A spa pump MUST have a minimum of 2 suction points (or 1 suction and skimmer) each suction having a flow rating equivalent or greater than the pump flow rate. ie combined flow rating of 2 suctions shall be at least double the pumps maximum flow rate.
Some spa suctions have differing flow ratings depending on installation method and components used.
This category will be undergoing continual change as more suctions become approved.
You must check you pump flow rate requirements when determining the correct suction type required. 
Incorrect pump/suction matching may lead to injury or death. 

Any doubts, please contact us before purchasing suction fittings or use a qualified spa technician. 

See further information below :

• A minimum of two functioning suction outlets per pump must be installed. Spa Suction outlets must be installed a minimum of 600mm apart, as measured from suction pipe center to suction pipe center. 
• Dual suction fittings shall be placed in such locations and distances to avoid "dual blockage" by a user. 
• Dual suction fittings shall not be located on seating areas or on the backrest for such seating areas. 
• The maximum system flow rate shall not exceed the flow rating of any listed suction outlet cover installed. In the event of one suction outlet being completely blocked, the remaining suction outlets serving the system shall have a flow rating capable of the full flow of the pump(s). 
• Never use pool or spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached. 
•Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately. 
•Two or more suction outlets per pump should be installed in accordance with latest standards.

Some spa suction fittings are available with vacuum break fittings allowing higher flow ratings - this is due to the vacuum break plumbing which, once the suction becomes blocked, will suck air from the vacuum break line / vent into the suction plumbing causing the pump to cavitate and lose suction, thus allowing a trapped person to be freed.

See our pump flow rate information page to help determine suction outlet flow requirements here



American Products PacFab Hyper Flow Spa Suction Cover - Discontinued NLA

SKU: ap452554ww

Discontinued NLA - no longer legal/safe - Replace with this suction fitting listed here and re-plumb to suit. American Products PacFab Hyper Flow spa suction cover These covers break easily. Replacement is e...

login or register to view pricing

Login/Register

CMP 4" Classic Grey Spa Suction - 423 lpm rated

SKU: cmp25203-001

CMP 4" spa suction Australian approved flow rate of 423 lpm / 112 GPM 100mm diameter cover. 34mm projection 83mm hole size required 2" / 50mm straight slip plumbing socket One centre screw securing ...

9 In Stock

login or register to view pricing

Login/Register

CMP 5" Classic Grey Spa Suction - 643 lpm rated

SKU: cmp25201-209-000

CMP 5" spa suction Australian approved flow rate of 643 lpm / 170 GPM 126mm diameter cover. 42mm projection 83mm hole size required 2" / 50mm straight slip plumbing socket One centre screw securing ...

login or register to view pricing

Login/Register

CMP 5" Graphite Grey Spa Suction - 643 lpm rated

SKU: cmp25201-207-000

CMP 5" spa suction Australian approved flow rate of 643 lpm / 170 GPM 126mm diameter cover. 42mm projection 83mm hole size required 2" / 50mm straight slip plumbing socket One centre screw securing ...

11 In Stock

login or register to view pricing

Login/Register

CMP 5" Stainless Steel Spa Suction - 651 lpm rated

SKU: cmp25200-202-000

CMP 5" spa suction Australian approved flow rate of 651 lpm / 172 GPM 126mm diameter cover. 34mm projection 83mm hole size required 2" / 50mm straight slip plumbing socket One centre screw securing ...

5 In Stock

login or register to view pricing

Login/Register

CMP Grey Spa Suction - 355 lpm rated

SKU: cmp25205-009

CMP spa suction Australian approved flow rate of 355 lpm / 94 GPM 95mm diameter cover. 24mm projection 58mm hole size required 1.5" / 40mm straight slip plumbing socket or 2" / 50mm spigot One x cen...

69 In Stock

login or register to view pricing

Login/Register

CMP Stainless Steel Spa Suction - 355 lpm rated

SKU: cmp25206-002-000

CMP spa suction Australian approved flow rate of 355 lpm / 94 GPM 90mm diameter cover. 24mm projection 58mm hole size required 1.5" / 40mm straight slip plumbing socket Two x screws securing cover, ...

505 In Stock

login or register to view pricing

Login/Register

Davey Aqua select Suction Cover

SKU: d12424

NO LONGER AVAILABLE Davey Aqua select Spa Bath Suction Cover Use S&P ASF523 (white) or ASF523cp (chrome) suction cover to replace - the threaded wall fitting will also require replacement (not just the cover...

login or register to view pricing

Login/Register

Edgetec Flexi-Flange Spa & Spa Bath Suction 192 lpm rated - Grey

SKU: e1300-gr

Edgetec suction Australian approved flow rate of 192lpm NB these same suctions were originally rated much higher and used in portable spas with 2-3hp pumps. It is NOT acceptable/legal to replace this suct...

4 In Stock

login or register to view pricing

Login/Register

Edgetec Flexi-Flange Spa & Spa Bath Suction 192 lpm rated - STARK WHITE

SKU: e1300-wh

Edgetec suction - Australian approved flow rate of 192lpm 100mm diameter cover. Female threaded wall fitting - suits Edgetec suction body only - sold separately. Stark White - original Edgetec white bat...

10 In Stock

login or register to view pricing

Login/Register

Edgetec Flexi-Flange Spa Bath Suction 192 lpm rated - Chrome

SKU: e1300-ch

DISCONTINUED in chrome - available white or grey. Edgetec spa bath suction face and wall fitting - chrome Face Diameter - 100mm, height off spa bath wall -24mm used on lanark spa baths and others Used ...

login or register to view pricing

Login/Register

Edgetec Flexi-Flange Spa Bath Suction COVER ONLY - 192 lpm rated - Chrome

SKU: e5514

DISCONTINUED IN CHROME - LIMITED TO STOCK ON HAND Edgetec spa bath suction face / cover only - chrome (white threaded frame not included.) Face Diameter - 100mm, height off spa bath wall -24mm Chrome ...

login or register to view pricing

Login/Register

Edgetec SLP (Super Low Profile) Spa Bath Suction - Chrome

SKU: e1320-ch

Edgetec SLP spa bath safety suction cover with threaded wall fitting SLP suction cover tool required for removal/installation. e7052 Chrome is a coating applied through electrolysis to a base material ...

25 In Stock

login or register to view pricing

Login/Register

Edgetec SLP (Super Low Profile) Spa Bath Suction - White 192 lpm rated

SKU: e1320-wh

Edgetec SLP spa bath safety suction cover with threaded wall fitting ​SLP suction cover tool required for removal/installation. e7052 ...

login or register to view pricing

Login/Register

Edgetec Spa Bath Suction Adaptor - Straight 1.5"/40mm

SKU: e1340

60mm hole size required 40mm socket ...

9 In Stock

login or register to view pricing

Login/Register

Edgetec Spa Bath Suction Tee Body 1.5"/40mm with End Cap

SKU: e1360

Edgetec Spa Bath Suction Tee body Hole size required - 60mm, 40mm/1.5" slip pipe connection ...

4 In Stock

login or register to view pricing

Login/Register

login or register to view pricing

Login/Register

flolux flosafe 40mm polished 316 Stainless Steel spa / pool safety suction - 40mm self aligning slip fit - 250lpm rated

SKU: flx002

flolux flosafe 40 - for that premium finish for your in-ground pool or spa. Maximum flow rate of 250 lpm. Can be used to replace any suction rated up to 250 lpm - ensure system flow rate and suctions match...

4 In Stock

login or register to view pricing

Login/Register

flolux flosafe 50mm polished 316 Stainless Steel spa / pool safety suction - 50mm self aligning slip fit - 280lpm rated

SKU: flx010

flolux flosafe 50 - for that premium finish for your in-ground pool or spa. Maximum flow rate of 280 lpm. Can be used to replace any suction rated up to 280 lpm - ensure system flow rate and suctions match...

5 In Stock

login or register to view pricing

Login/Register

flolux flosafe 50mm polished 316 Stainless Steel spa / pool safety suction - 50mm Threaded - 280lpm rated

SKU: flx011

flolux flosafe 50 threaded - for that premium finish for your in-ground pool or spa. Maximum flow rate of 280 lpm. Can be used to replace any suction rated up to 280 lpm - ensure system flow rate and sucti...

1 In Stock

login or register to view pricing

Login/Register

LVJ 2" Suction Assembly - Black - 156 GPM / 590 LPM

SKU: lvjL-3802B

LVJ 2" black safety suction Flow rated to 156GPM / 590 LPM 132mm diameter, 43mm projection. Requires a 84mm hole diameter. 2" socket pipe connection Held with 2 small screws on sides ...

2 In Stock

login or register to view pricing

Login/Register

Markon Suction Assembly - Dome Series Super Low profile - Chrome

SKU: mksc0803se2626

Markon Dome series super low profile suction assembly complete - chrome. 91mm OD cover - push click fit suction cover. Approx 8mm projection in from wall of bath at centre of the suction cover. 70mm ...

10 In Stock

login or register to view pricing

Login/Register

Markon Suction Assembly - Low profile - Chrome - Suits newer Stylus & others

SKU: mksc0503st0726

Markon low profile suction assembly complete - chrome. 100mm OD cover - push click fit suction cover. 70mm hole required. 40mm plumbing Tee body with bung MUST be installed as a pair Chrome ...

15 In Stock

login or register to view pricing

Login/Register

Markon Suction Assembly - Safe-Flo - Chrome

SKU: mksc0403-K

Markon Safe-Flo suction assembly complete - chrome. 90mm OD cover - push click fit suction cover. Approx 8mm projection in from wall of bath at centre of the suction cover. 70mm hole required. 40mm...

8 In Stock

login or register to view pricing

Login/Register